Elog Entry 2021-05-27: Difference between revisions
Jump to navigation
Jump to search
(Created page with "=Detector testing= *EHAT:PMT5, 50V, ramps up, 0.08uA readback. LED cable now connected with new connector. Works. Using driver channel 5. ~250pC at 70%.") |
|||
| (16 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Detector testing= | =Detector testing= | ||
*EHAT: | *EHAT:PMT4, 50V, ramps up, 0.08uA readback. LED cable now connected with new connector. Works. Using driver channel 5. ~250pC at 70%. | ||
*ELBD:PMT0, 200V, ramps up, 0.2uA readback. works. 550pC at 50% with elbd:pmt0 cables. installed at egun window. led driver 8. hv, sig 4. | |||
*ELBT:PMT1C, 200V, ramps up, 0.2uA readback. works. 285pC at 50% with elbt:pmt1c cables.installed on west side. led driver 2. hv, sig, 3. | |||
*Tested new ELBT:PMT1B with EABT:PMT1:LED label on roof in led driver channel 1. Works at 200V, 0.21uA, 300pC at 50%. | |||
=Detector installation= | |||
*Installed spare PMT (previous ELBT:PMT1A) at window on gun. Connected cables for ELBD:PMT0 because that set had LED cable. | |||
*Place mic stand on EAST side in low energy section for ELBT:PMT1B installation. Connected all cables. All labeled correctly. | |||
*Note, LED cable label for PMT1C is EACB:LED. | |||
*Found that cable on the roof labeled EABT:PMT1:SIG is actually ELBD:PMT0:LED. Will connect this to channel 8 in driver. Getting 225pC at 45%. Also tested with LED driver channel 8. | |||
*CHANGE OF PLAN: | |||
*Using PMT0 as the diagnostics detector after all with pmt0 cables. sig, hv, channel 4 and led ch8. doing this as old pmt1b led doesnt't seem to work? or detector doesn"t work? tested with pmt0 cables and pmt1b cables, but no response. | |||
*using former pmt1a is now pmt1b, NM 4289. with pmt1b cables. | |||
ELBD:PMT0 used as diagnostic (temporary): | |||
[[Image:20210527_142330.jpg|500px|Low energy diagnostics ELBD:PMT0]] | |||
ELBT:PMT1B: | |||
[[Image:20210527_142309.jpg|500px|Low energy diagnostics ELBT:PMT1B]] | |||
ELBT:PMT1C: | |||
[[Image:20210527_132721.jpg|500px|Low energy diagnostics ELBT:PMT1C]] | |||
=LED labels= | |||
*Connected EACB:PMT1:LED to LED driver channel 2 on roof. Cable will be used for to ELBT:PMT1C detector in hall. Present label is EACB:PMT1:LED. | |||
*Found that cable on the roof labeled EABT:PMT1:SIG is actually ELBD:PMT0:LED. Will connect this to channel 8 in driver. | |||
*ELBT:PMT1B:LED and ELBT:PMT1C:LED on roof, channels 1 and 2 need new labels. | |||
Latest revision as of 22:27, 27 May 2021
Detector testing
- EHAT:PMT4, 50V, ramps up, 0.08uA readback. LED cable now connected with new connector. Works. Using driver channel 5. ~250pC at 70%.
- ELBD:PMT0, 200V, ramps up, 0.2uA readback. works. 550pC at 50% with elbd:pmt0 cables. installed at egun window. led driver 8. hv, sig 4.
- ELBT:PMT1C, 200V, ramps up, 0.2uA readback. works. 285pC at 50% with elbt:pmt1c cables.installed on west side. led driver 2. hv, sig, 3.
- Tested new ELBT:PMT1B with EABT:PMT1:LED label on roof in led driver channel 1. Works at 200V, 0.21uA, 300pC at 50%.
Detector installation
- Installed spare PMT (previous ELBT:PMT1A) at window on gun. Connected cables for ELBD:PMT0 because that set had LED cable.
- Place mic stand on EAST side in low energy section for ELBT:PMT1B installation. Connected all cables. All labeled correctly.
- Note, LED cable label for PMT1C is EACB:LED.
- Found that cable on the roof labeled EABT:PMT1:SIG is actually ELBD:PMT0:LED. Will connect this to channel 8 in driver. Getting 225pC at 45%. Also tested with LED driver channel 8.
- CHANGE OF PLAN:
- Using PMT0 as the diagnostics detector after all with pmt0 cables. sig, hv, channel 4 and led ch8. doing this as old pmt1b led doesnt't seem to work? or detector doesn"t work? tested with pmt0 cables and pmt1b cables, but no response.
- using former pmt1a is now pmt1b, NM 4289. with pmt1b cables.
ELBD:PMT0 used as diagnostic (temporary):
ELBT:PMT1B:
ELBT:PMT1C:
LED labels
- Connected EACB:PMT1:LED to LED driver channel 2 on roof. Cable will be used for to ELBT:PMT1C detector in hall. Present label is EACB:PMT1:LED.
- Found that cable on the roof labeled EABT:PMT1:SIG is actually ELBD:PMT0:LED. Will connect this to channel 8 in driver.
- ELBT:PMT1B:LED and ELBT:PMT1C:LED on roof, channels 1 and 2 need new labels.